Thanks. I think I've got it figured out. Going to sit down with some glue and some zip kicker and give it a shot momentarily.
I will say that the person who made these is a pretty awesome dude!!
| Tactical Command http://www.tacticalwargames.net/taccmd/ |
|
| Blood Slaughterer Assembly? http://www.tacticalwargames.net/taccmd/viewtopic.php?f=7&t=28688 |
Page 1 of 1 |
| Author: | Xenocidal Maniac [ Fri Dec 12, 2014 9:44 am ] |
| Post subject: | Blood Slaughterer Assembly? |
I've come into possession of some OOP Blood Slaughterer models. Six of them, to be exact. I haven't any clue how to put these guys together! I searched high and low to try to find a clear picture of one, but couldn't come up with anything that would shed some light on which little tiny leg / claw thingy goes where. Any ideas? |
|
| Author: | Apocolocyntosis [ Fri Dec 12, 2014 10:44 am ] |
| Post subject: | Re: Blood Slaughterer Assembly? |
http://wargamingworkshop.files.wordpres ... =900&h=171 pictures of completed ones here, from Helge the big legs go at the back (+1 long claw each), the small legs go at the front (+1 short claw each). Think there were instructions at one point, but whoever made them seems to have deleted them during the purge. I might have saved them to an old HDD at one point, can check at the weekend. |
|
| Author: | Dobbsy [ Fri Dec 12, 2014 6:15 pm ] |
| Post subject: | Re: Blood Slaughterer Assembly? |
I remember the leg connection points being the most perplexing due to the top of the leg's shape and the sections they were to be glued to being oddly difficult to recognise. I needed to trim the top of the leg to get the right shape and glue it to the body IIRC. I had the instructions too but have no idea where they are now. I think I also tried to match them up and see how the mini balances which helped me construct them. |
|
| Author: | moredakka [ Fri Dec 12, 2014 7:20 pm ] |
| Post subject: | Re: Blood Slaughterer Assembly? |
I downloaded pictures of the FW 40k model which helped a lot. |
|
| Author: | Xenocidal Maniac [ Fri Dec 12, 2014 9:33 pm ] |
| Post subject: | Re: Blood Slaughterer Assembly? |
Dobbsy wrote: I remember the leg connection points being the most perplexing due to the top of the leg's shape and the sections they were to be glued to being oddly difficult to recognise. Yes! This is exactly the issue. The legs don't appear to fit anywhere at the correct angle. I think I've sort of figured out where the front legs go, but the rear legs are still a bit of a mystery. |
|
| Author: | Apocolocyntosis [ Fri Dec 12, 2014 9:47 pm ] |
| Post subject: | Re: Blood Slaughterer Assembly? |
same place as on the FW one Look at pictures, back legs go on the 2 lil nubs sticking out the back just above the waist http://www.forgeworld.co.uk/Images/Prod ... ererp4.jpg |
|
| Author: | Xenocidal Maniac [ Sun Dec 14, 2014 8:52 am ] |
| Post subject: | Re: Blood Slaughterer Assembly? |
Thanks. I think I've got it figured out. Going to sit down with some glue and some zip kicker and give it a shot momentarily. I will say that the person who made these is a pretty awesome dude!!
|
|
| Author: | Apocolocyntosis [ Sun Dec 14, 2014 10:59 am ] |
| Post subject: | Re: Blood Slaughterer Assembly? |
Xenocidal Maniac wrote: I will say that the person who made these is a pretty awesome dude!! I'd reserve comment until you've got a couple built, recon you'll be cursing him fairly soon
|
|
| Page 1 of 1 | All times are UTC [ DST ] |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|