I did one, but never printed it.
Attachment:
oszlop.png [ 292.3 KiB | Viewed 4079 times ]
Did small ones too, for 6mm scale figures.
| Tactical Command http://www.tacticalwargames.net/taccmd/ |
|
| Statue Plinths http://www.tacticalwargames.net/taccmd/viewtopic.php?f=28&t=30196 |
Page 1 of 1 |
| Author: | Stormwind [ Sun Aug 30, 2015 8:42 pm ] |
| Post subject: | Statue Plinths |
I love 28mm models used as statues of heroes in Epic or Warmaster. Forge World used to do a statue tower but that is now rare and expensive on eBay. Surely another provider of resin produces nice little plinths (or tall ones!) suitable as terrain for Epic nowadays, any suggestions? |
|
| Author: | Blip [ Sun Aug 30, 2015 9:30 pm ] |
| Post subject: | Re: Statue Plinths |
Wedding cake stands. |
|
| Author: | leaxe [ Wed Sep 02, 2015 9:15 am ] |
| Post subject: | Re: Statue Plinths |
I did one, but never printed it. Attachment: oszlop.png [ 292.3 KiB | Viewed 4079 times ] Did small ones too, for 6mm scale figures. |
|
| Author: | Stormwind [ Wed Sep 02, 2015 12:55 pm ] |
| Post subject: | Re: Statue Plinths |
Whoa, that looks great! What size is that? |
|
| Author: | leaxe [ Wed Sep 02, 2015 1:18 pm ] |
| Post subject: | Re: Statue Plinths |
It could be any size. I could resize it. Currently the green part is 42mm high. The top and the bottom are around 5mm each. I also had some braziers. Just need to sculpt a little fire in them. 
|
|
| Author: | lylekelm [ Thu Sep 03, 2015 1:05 am ] |
| Post subject: | Re: Statue Plinths |
very nice leaxe |
|
| Author: | Stormwind [ Thu Sep 03, 2015 3:30 pm ] |
| Post subject: | Re: Statue Plinths |
Wow! So those would be the right size for a small model on top. I was imagining the kind that Forge World used to make: http://www.powerdice.com/epic/TERRAIN/F ... alogue.jpg I believe they were large enough to put a plastic 28mm figure on the top. |
|
| Author: | leaxe [ Fri Sep 04, 2015 7:18 am ] |
| Post subject: | Re: Statue Plinths |
as this is still scalable, I could make it bigger. The base on top is 17mm across. I have no marines around, just an inquisitor. It spreads its legs to 20mm approximately. I can make some variants if there is real interest. |
|
| Author: | leaxe [ Fri Sep 04, 2015 7:27 am ] |
| Post subject: | Re: Statue Plinths |
also made some braziers last year. As I did them in 123D design and my Mac is packed up in the garage, I can not access the files. But redid it now. I was planning to use these on building corners, on top of slim pillars and next to a gate. Attachment: brazier.png [ 134.93 KiB | Viewed 3972 times ] The fire would be done with greenstufff or cotton |
|
| Author: | Kyrt [ Fri Sep 04, 2015 5:43 pm ] |
| Post subject: | Re: Statue Plinths |
I have one of the FW plinths and it should be ideal for a 40k model on top I expect. At least that's what I plan to do with it. |
|
| Page 1 of 1 | All times are UTC [ DST ] |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|
